Original web-site | Product list | Company picture | Company magazine
Home About us News Product Project achievement Make strength Guestbook Contact us Chinese
Home > Product > φ4.2×14m Cement Mill
φ4.2×14m Cement Mill
φ4.2×14m Cement Mill
(Central double slide shoe)
    一、Technical parameters & performances of cement mill
2、Capacity: 180t/h (configures roller press + Scattered classifier or V separator, inlet moisture content ≤0.5%, inlet temperature≤50℃,Blaine:340-360m2/kg
3、Rotating speed of mill:15.8r/min
4、Supporting type: double side shoe
5、Transmission type: central driving
6、Chambers: 2pcs
7、Grinder load: 240t (max)
8、Main motor:
Type:YRKK1000-8  Power:3550kW  Rotating speed:740r/min
    9、Main reducer(*****):
    (1) Type:JS150-B
    (2) Transmission power:3550KW
    (3) Output rotating speed:15.8r/min
    10、Slow driving device
    (1) Type:JMS660
    (2) Motor power:45kW
    (3)Motor rotating speed 740r/min
    (4) Transmission ratio:98.58:1
    11、Diaphram coupling
    12、Oil station (configures main reducer)
    (1) Nominal flow rate:400L/min
    (2) Oil pump type:XBZ-400
    (3) Motor power:18kW
    (4) Motor rotating speed:1460r/min
    (5) Cooling area:30m2
    (6) Cooling water volume:35t/h
    (7) Heater power:4×6=24KW
13、Cooling type: water cooling
    14、Lubrication type ( thin oil station NC-63S)
    (1)Low pressure system
     Flow rate:80L/min   Oil supply pressure:0.4MPa
     Oil supply temperature:40±3℃
     Motor:Y112M-6  2.2kW  380V
    (2) High voltage system
     Pump type:10SCY14-1B
     Flow rate:2.5L/min
     Oil supply pressure:32MPa
     Motor:Y112M-4  4kW  380V
    (3) Other performances
Oil cooler GLCQ3-70.63
Nominal pressure:0.63MPa
Cooling area:7m2
Inlet water temperature:<28℃
  Heater power:SRYZ-220/4   Power 4KW  220V
  Working media:N33-N320
15、 Equipment weight:257.7t(Without grinder & mill transmission device)
    二、 Main spare parts and material quality
1、 Shell Q235-C  δ=40mm   Entire annealing
    Max. outline dimension φ4390×16620   Weight of max. part: 96t
2、 Slide ring:20g-Z25   Thickness 95
3、 Web of slide ring 20g, Thickness 80
4、 Supporting:ZG270-500
Bush lining( Babbitt Metal ZSnSb11Cu6)
Idler roller:45
Bump ball:34CrNi3MoA
Ball base:ZG270-500
Bottom plate:Q235-B
5、 Liner: wear-resisting alloy steel
6、Thin oil station   NC-63S two sets for each pc, 63l/min supplied oil of low pressure oil for each pc
    7、Controller of thin oil station
   三、Supply range

1、Rotary section
1 set
2、Feed device
3、Slide shoe device
2 sets/pc
4、Discharge device
5、Liner & diaphram
6、Main motor YRKK1000-8  3550kW
7、Main reducer JS150-B
8、Slow driving device  HMS660
9、Diaphram coupling  JL150-00
10、Thin oil station  NC-63S
2 sets
11、Controller of thin oil station
1set per pc
13、Anchor bolts

Ohter Products
Tube mill
Cement Mill
Grinding equipment
PMG series high efficient ball mill
dia.2.6*13m Super fine slag mill
dia. 3.2*13m Slag mill
dia. 3.5*10m raw mill
φ3.5×13m High fine mill ( Edge-driving transmission)
dia. 3.8*(7.5+1.5)mRaw mill
φ3.8×13m Cement Mill
dia. 4.2*13m Center driving Cement mill
dia. 4.2*13m Cement mill
Φ4.2×13m Cement mill ( Single edge double driving )
φ4.2×14m Cement Mill
diameter 4.2*14.5m cement mill
dia.4.2*15m cement mill
M42130 Cement mill Technical performance
dia. 4.6*(10+3.5)m Middle discharging raw mill
φ3.2×(6.5+2)m Air swept coal mill、coal mill
φ3.2×(6.75+2)m Coal mill
φ3.4×(6+3)m Coal mill
φ3.8×(6.5+3)m Technical performances of air swept coal mill
Main bearing of tube mill utilizing rolling bearing
Calcium carbonate superfine grinding mill/quartz sand grindi
Process Introduction of Pengfei Φ3.2×13m High Fine Open Circ
Ф5×15 m Cement Mill
Cement grinding station
Modify cement grinding process and enhance product qualit
φ4.6×14m Cement Mill
φ4.4×13m Cement mill
dia.4.4*13.5m cement mill
Technical performance of φ4.6×14.5m cement mill
dia. 4.6*15.5m cement mill
 打印本页 [ 关闭窗口 ] 向上
Copyright © Jiangsu Pengfei Group Co.,Ltd. All Rights Reserved.